ASME B18.3-2003 pdf download
ASME B18.3-2003 pdf download.Socket Cap, Shoulder, and Set Screws，Hex and Spline Keys (Inch Series). (14) See Table 7 for spline socket dimensions and Mandatory Appendix I for gaging of spline sockets. (15) See Table 6 for hexagon socket dimensions and Mandatory Appendix I for gaging of hexagon sockets. (16) Bearing Surface. The runout of the conical bearing surface shall be...
ASME B18.6.3-2003 pdf download
ASME B18.6.3-2003 pdf download.Machine Screws and Machine Screw Nuts. Recess gaging values are included in the respective dimensional tables, including the reference dimensions of recess diameter, wing width, and total recess depth. The gaging method and specifications for gages are contained in Appendix III. Recess wobble gages, gaging procedures, and permissible limits are given in Appendix IV. 2.1.4 Slot. The...
ASME A112.19.10-2003 pdf download
ASME A112.19.10-2003 pdf download.DUAL FLUSH DEVICES FOR WATER CLOSETS. (6) record the results of each test separately. (b) Performance Requirement. All residual paper shall be removed from the well (not visible) in (1) any two of the three reduced volume flushes and (2) all residual and new paper load added in the following single conventional long flush Failure to perform...
ASME Y14.6-2001 pdf download
ASME Y14.6-2001 pdf download.SCREW THREAD REPRESENTYATION. ASME 5th. registered tade.nirk of The Amencan Society ol Mechanical Engineer.. This code or standard was desetop.d under procedures accredited as meeting the criteri. for American National Standard. The Standards Committee that approved th. code or standard was balanced to assure that individuals from competent and concerneo interests have had an opportunity to participate...
ASME RAM-2-2016 pdf download
ASME RAM-2-2016 pdf download.Reliability, Availability, and Maintainability Program Development Process for Existing Power Plants. The RAM program shall address plant maintainability for the following areas: (a) access — ease of access to work locations and the ability to work safely without special rigging and tools; assurance that workers have access to equipment that may need service, i.e., equipment is designed...
ASME PTC-2-2001 pdf download
ASME PTC-2-2001 pdf download.DEFINITIONS AND VALUES. 3.1 PRIMARY DEFINITIONS AND SYSTEMS OF UNITS The dimensions of mass, length, and time are related to forces as follows in the various systems of units. A force of one pound applied to a mass of one slug (also known as the geepound) will accelerate the mass at the rate of one ft/sec2. A...
ASME PTC 47-2006 pdf download
ASME PTC 47-2006 pdf download.Integrated Gasification Combined Cycle Power Generation Plants. inert niatter: constituents of coal or gas that decrease its efficiency in use, e.g., mineral matter (ash) in coal and moisture in fuel for combustion. Also refers to nonreactive gases such as nitrogen or argon that may be contained in the air or oxygen used for the gasification process,...
ASME B89.7.1-2016 pdf download
ASME B89.7.1-2016 pdf download.Guidelines for Addressing Measurement Uncertainty in the Development and Application of ASME B89 Standards. This Technical Report uses the term adjustments when discussing the service activities undertaken to modify the metrological characteristics of measuring equipment; the typical purpose of adjustments is to bring measuring equipment back within specified MPEs or tolerance limits. Measurements used for determining necessary...
ASME B89.1.13-2001 pdf download
ASME B89.1.13-2001 pdf download.MICROMETERS. Al GENERAL This Appendix is intended to provide gcneiai guidance on good operating procedures involving ,iucrometen, spreifically the outside. inside, and depth microrn eICTS A2 MICROMETER, OUTSIDE A2.1 Zero Setting. Mechanical Micrometer Prior to talung measurements, the zero point of the micrometer must be established Zero selttng is the first step of operation with outside, inside,...
ASME A112.19.13-2001 pdf download
ASME A112.19.13-2001 pdf download.ELECTROHYDRAULIC WATER CLOSETS. 1.4 Electrohydraulic Water Closet An clcctmhydraulic water closet is a siphonic or wash.down water closet as described in ASME A1l2.l9.2M with a nenmechanical trap seal. The water closct incorporates clectncal motors). pump(si. and cornrnlkrs to facilitate the flushing action. In this Standard, the term waler ck?.wt means an electrohydraulic staler closet unless otherwise indicated....