ASME B30.7-2001 pdf download
ASME B30.7-2001 pdf download.BASE-MOUNTED DRUM HOISTS. parts; on environmental conditions causing corrosion or wear; and on many variables that must be considered in each individual case. The rules given in the Standard must be interpreted accordingly, and judgment used in determining their application. Some of the provisions of this Standard require compliance with information found in manuals or other documents...
ASME B29.22-2001 pdf download
ASME B29.22-2001 pdf download.DROPFORGEDRIVETILESS CHAINS,SPROGKETEETH DRIVE CHAINVDRIVE DOGS. The drop forged rivetless chain has widespread use in many industries on trolleys. scraper flights, assembly. and similar conscynes. H.ccausc matciials do not tend to pack in its open stnselure. the drop forged rivclle.ss chain is used extensively For flight conveyors. Its design permits both horitontal and vertical operation over irregular routes,...
ASME B20.1-2006 pdf download
ASME B20.1-2006 pdf download.Safety Standard for Conveyors and Related Equipment. belt tripper: a device incorporating a system of pulleys that causes the conveyor belt to discharge material at one or more points along the length of the conveyor. boom: a cantilevered member or structure that may be hinged, fixed, or pivoted. brake: a friction device for slowing down conveyor components,...
ASME B18.5.2.1M-2006 pdf download
ASME B18.5.2.1M-2006 pdf download.Metric Round Head Short Square Neck Bolts. General. ASME Standards are developed and maintained with the intent to nrpnsent the consensus of concerned interests. As such. users of this Standard may interact with the Committee by requesting interpretations, proposing revisions, and attending Committee meetings. Correspondence should be addressed to: Secretary. 818 Standards Committee The American Society of...
ASME B18.2.3.4M-2001 pdf download
ASME B18.2.3.4M-2001 pdf download.METRIC HEX FLANGE SCREWS. If verif able in-process inspeclion is used, inspection sample sizes and reporting shall be in accordance with the applicable ASME. ASTM. or SAF quality system consensus standard. (b) For nondesignated dimensional characteristics, the piuvisions of ASME BIX.18.IM shall apply. Should a nondesignated dimension be determined to be outside its specifed limits. it shall...
ASME B16.36-2006 pdf download
ASME B16.36-2006 pdf download.Orifice Flanges. 8.2 Location 8.2.1 Measurement. The24mm(0.94in.)dimension for raised fact and 19 mm (0.75 in.) for ring joint shall be measured at the bore. 8.2.2 IdentifIcation. For ring ,oint flanges requiring dltL’TdtiOfl Ut pussun tap location due to interfince with the ring groove other than methods provided in this Standard, such alteration shall be identified per agreement...
ASME B16.23-2016 pdf download
ASME B16.23-2016 pdf download.Cast Copper Alloy Solder Joint Drainage Fittings: DWV. 2 GENERAL 2.1 Relevant Units ThLs Standard states values in both SI (Metric) and U.S. Customary units. These systems of units are to be regarded separately as standard. Within the text, the U.S. Customary units are shown in parentheses or in separate tables that appear in Mandatory Appendix 1....
ASME B73.1M-2001 pdf download
ASME B73.1M-2001 pdf download.SPECIFICATION FORHORIZONTAL END SUCTIONCENTRIFUGAL PUMPS FOR CHEMICAL PROCESS. (c) Pump Casing Jacket (d) Bolt on External Heating and Cooling Jacket (e) Bearing Housing Cooling 4.3.6 Gasket(s). The casing-to-cover gasket shall be confined on the atmospheric side to prevent blowout. 4.4 Impeller 4.4.1 Types. Impellers of open. semi-open. and closed designs are optional. 4.4.2 Adjustment. Means for external...
ASME B16.22-2001 pdf download
ASME B16.22-2001 pdf download.WROUGHT COPPERAND COPPER ALLOY SOLDER JOINTPRESSURE FITTINGS. (hi Other coppers and copper alloys are permitted. provided they meet the chemical requirements of 84% minimum copper and 16% maximum zinc, and provided the fittings produced from the copper alloy meet all the mechanical and corrosion-resistant properties for the end purposes of the fittings. The composition of the copper...
ASME B16.3-2006 pdf download
ASME B16.3-2006 pdf download.Malleable lron Threaded Fittings. Use of a pressure rating at a material temperature other than that of the contained fluid is the responsibility of the user and subject to the requirements of any applicable code. (d) Class 300 street elbows are not recommended for pressures above 600 psi. 3 SIZE 3.1 Nominal Pipe Size As applied in...